Appliance Dimensions & Fit Guide: Printable Measurement Template for Kitchens
appliance dimensionskitchen planninginstallationmeasurement templateappliance compatibility

Appliance Dimensions & Fit Guide: Printable Measurement Template for Kitchens

AAppliances.link Editorial Team
2026-11-10
7 min read

Use this appliance dimensions chart and printable checklist to measure openings, clearances, door swings, connections, and delivery paths.

Buying a replacement appliance is easier when you measure the space before you shop. This appliance dimensions and fit guide includes a reusable checklist, typical size ranges, clearance reminders, and a printable measurement template for refrigerators, ranges, dishwashers, washers, and dryers.

Overview

An appliance can match the advertised width and still fail to fit because of its depth, height, door swing, hoses, plug, handles, leveling feet, or the route into the room. Treat the opening and the delivery path as separate measurements. The cabinet opening may accommodate an appliance that cannot pass through a doorway or turn at a hallway corner.

Use the chart below for early planning only. These are common planning ranges, not specifications for a particular model. Always compare your measurements with the manufacturer’s installation guide, which may list the product-body dimensions separately from dimensions including handles, doors, hinges, controls, or required clearances.

ApplianceCommon width rangeCommon height rangeTypical depth planning note
Refrigerator, standard depthAbout 30–36 inchesAbout 66–70 inchesOften roughly 30–36 inches before handles and door clearance
Refrigerator, counter depthAbout 30–36 inchesAbout 66–70 inchesOften roughly 24–30 inches before handles and door clearance; capacity and door design vary
Freestanding rangeAbout 30 inchesAbout 36 inchesOften about 25–28 inches for the cabinet, with controls and handles adding depth
Built-in or slide-in rangeOften about 30 inchesAbout 36 inchesConfirm the manufacturer’s opening, countertop, and rear-clearance requirements
Built-in dishwasherOften about 24 inchesAbout 34–35 inches, adjustableUsually designed for a standard cabinet opening, but connections occupy space behind or below
Compact dishwasherOften about 18 inchesAbout 34–35 inchesVerify whether the model is built-in, countertop, or portable
Front-load washerAbout 27 inchesAbout 38–40 inchesAllow extra depth for hoses, door, and opening the front door
Top-load washerAbout 27 inchesAbout 38–44 inchesMeasure overhead space for the lid to open fully
Electric or gas dryerAbout 27 inchesAbout 38–40 inchesAllow room for the vent, gas line where applicable, or power connection

“Counter depth” is not a universal finished-depth measurement. A counter-depth refrigerator may still project beyond the counter once its doors and handles are included. For a fuller comparison, see our counter-depth versus standard-depth refrigerator guide.

Checklist by scenario

Refrigerator alcove

  1. Measure the opening width at the top, middle, and bottom. Record the smallest number.
  2. Measure height on the left, center, and right. Check for a sloping floor or cabinet that reduces the opening.
  3. Measure depth from the back wall to the front edge of the counter, cabinet, or adjacent obstruction.
  4. Record the depth with doors and handles included in the product specification, not only the cabinet depth.
  5. Map the hinge side, door swing, and the space needed to remove drawers or shelves for cleaning.
  6. Check whether the water line, electrical outlet, wall, or baseboard occupies usable depth.

For a counter-depth refrigerator, decide how much projection is acceptable before selecting a model. Also confirm that both doors can open far enough for the interior bins to clear the adjacent wall or cabinet.

Range, cooktop, or oven opening

  1. Measure the width between the cabinets at the front and rear of the opening.
  2. Measure countertop height and check whether the floor is level with the surrounding cabinets.
  3. Record the depth of the countertop and the depth of nearby cabinet faces.
  4. Identify the fuel or electrical connection and its location. The connection should not interfere with the appliance body or installation instructions.
  5. Check the manufacturer’s requirements for the wall, backsplash, overhead cabinets, and ventilation.

Do not assume that a range advertised as a certain width will fill an opening exactly. Product dimensions and recommended opening dimensions can differ, and slide-in models may require more specific countertop or rear-wall conditions.

Dishwasher under a counter

  1. Measure the opening width at several points, especially if the cabinets are older or uneven.
  2. Measure from the finished floor to the underside of the counter. Include flooring that may have been installed after the cabinets.
  3. Measure opening depth from the front of the cabinet face to the back wall.
  4. Locate the water supply, drain connection, and electrical connection. Confirm that the hoses can route without being pinched.
  5. Open the dishwasher door and check for conflicts with the opposite cabinet, island, or walkway.

A dishwasher may physically enter an opening but remain difficult to level if the floor is raised or the opening is not square. Include installation access in your plan.

Washer and dryer space

  1. Measure width, height, and depth of the laundry space, including the depth of the door or closet.
  2. For a front-load washer or dryer, measure the room needed to open the door and stand in front of it.
  3. For a top-load washer, measure from the floor to the lowest obstruction above the lid.
  4. Allow space behind the machines for water hoses, the drain, power cord, gas connection where applicable, or dryer venting.
  5. Check whether a stacked pair requires a compatible stacking kit and sufficient overhead height.
  6. Confirm that the delivery path can accommodate the appliance width, depth, and turning radius.

For a discussion of loading access and space tradeoffs, compare front-load and top-load washers. Electrical and connection details are covered in the appliance electrical requirements guide.

Printable measurement template

Copy this checklist into a notes app or print it before visiting a retailer. Write measurements in inches or centimeters, but do not mix units.

PROJECT: ____________________   DATE: __________   ROOM: ____________________

APPLIANCE: __________________   MODEL SHORTLIST: _____________________________

OPENING
Width:     top ______  middle ______  bottom ______  smallest ______
Height:    left ______ center ______  right ______   smallest ______
Depth:     back wall to obstruction ______
Floor level / opening square? ________________________________________________

CLEARANCE
Left side ______  Right side ______  Top ______  Rear ______
Door swing and hinge side: _________________________________________________
Handle or door projection: ________________________________________________

CONNECTIONS
Outlet / circuit: __________________  Water: ________________________________
Drain: ____________________________  Gas or vent: __________________________

DELIVERY PATH
Entry door ______  Hallway ______  Tight turn ______  Stairs / elevator ______
Remove door or trim? ______________________________________________________

MODEL CHECK
Product width ______  Product height ______  Product depth ______
Depth with doors/handles ______  Installation clearance ______
Manufacturer installation guide reviewed?  Yes / No

What to double-check

Product versus opening dimensions: Use the smallest opening measurement and compare it with the model’s required opening, not just its headline dimensions. Look for a separate installation diagram.

Door and drawer movement: A refrigerator may fit when closed but fail when a drawer needs to extend. A dishwasher door may block a walkway. A washer door may hit a wall. Sketch the open position on the floor with painter’s tape.

Ventilation and connections: Appliances need room for specified airflow, hoses, cords, ducts, or fuel connections. Do not compress a dryer vent or force a water line into a sharp bend. Follow the product instructions and local installation requirements.

Leveling and service access: Check whether feet can be adjusted and whether a technician could access the appliance later. A very tight fit can make routine maintenance or removal unnecessarily difficult.

Delivery measurements: Measure the clear width of exterior and interior doors, gates, stairways, and turns. Note low ceilings, railings, trim, and refrigerator doors that may need removal by the delivery or installation team.

When assessing a specific appliance, use its model number and installation sheet rather than relying on a retailer thumbnail. Our model number lookup guide explains where to find identifying information on common appliances.

Common mistakes

  • Measuring only once: Walls and cabinets are not always parallel. Measure multiple points and use the smallest result.
  • Ignoring handles: Handle depth can change how far a refrigerator projects into a walkway.
  • Forgetting the floor: New flooring can reduce a dishwasher or range opening height.
  • Using cabinet depth as appliance depth: Doors, controls, hinges, and ventilation space may extend beyond the cabinet line.
  • Leaving no working clearance: A machine that cannot be pulled forward may be hard to repair or disconnect.
  • Assuming all 24-inch dishwashers or 30-inch ranges are interchangeable: Width is only one compatibility check; height, connections, door clearance, and opening requirements matter too.
  • Skipping the delivery route: A successful kitchen measurement does not guarantee the appliance can reach the kitchen.

If you are buying used, inspect the model plate and measure the actual appliance rather than trusting a seller’s description. The used appliance inspection guide can help you check fit and condition together.

When to revisit

Save the completed template with the appliance model number, installation guide, and photos of the opening. Recheck it whenever you replace an appliance, change flooring or countertops, remodel cabinets, move an outlet, alter a water or gas connection, or plan a delivery through a different entrance.

Review the comparison table before seasonal shopping and after major appliance launches, because product dimensions and available configurations change. Recheck clearance and ventilation guidance annually, and confirm local requirements with a qualified installer when the project involves gas, dedicated electrical circuits, structural changes, or permanent ventilation.

Your final pre-order action list is simple: measure the opening three ways, measure the delivery route, record connections, mark the open-door footprint, read the model-specific installation guide, and keep a margin for leveling and service access. Only place the order after every item is documented.

Related Topics

#appliance dimensions#kitchen planning#installation#measurement template#appliance compatibility
A

Appliances.link Editorial Team

Senior Home Appliances Editors

Senior editor and content strategist. Writing about technology, design, and the future of digital media. Follow along for deep dives into the industry's moving parts.